Zum Inhalt springen
A technician using integrated black gloves to handle a glass vial inside a SKAN "spectra" sterility testing isolator.

Sterility testing

Reliable batch release starts with a test environment you can trust

Mehr erfahren

Day 14 of incubation: one canister shows turbidity. What follows is familiar to every QC lab – the batch is on hold, an investigation starts and earlier batches are called into question. And one question is hard to answer: was the product contaminated, or the test?

The test for sterility is the final quality control step before an aseptically manufactured batch is released. The harmonized pharmacopoeias (Ph. Eur. 2.6.1, USP <71>, JP) require it for every product for which sterility is prescribed. Yet only a small fraction of the batch is tested – and a positive result can only be invalidated if a laboratory error is clearly proven.

At the same time, expectations are rising. Annex 1 requires sterility testing to be part of the contamination control strategy (CCS), release timelines are tight, and every manual step can lead to a wrong result.

This page brings together what matters for reliable sterility testing – from typical challenges and critical process steps to proven solutions and current trends.

At a glance

Key challenges in sterility testing

  • False positive results

    Contamination during testing can lead to the loss of whole batches

  • False negative results

    Undetected product contamination reaches the patient

  • Human error

    Almost every wrong result goes back to manual handling.

  • Integration into the CCS

    Annex 1 requires a risk-based approach for quality control as well

  • Product and packaging diversity

    Large volumes, antimicrobial products or H₂O₂-permeable packaging do not fit every test environment

  • Undefined background environment

    No binding standard defines the room around a sterility testing isolator

Critical points for test results

Typical sterility testing workflow (membrane filtration)

  • 1

    Preparation and loading

    Cleaning, wipe disinfection and correct loading decide whether the decontamination agent reaches every surface. Residues, touching materials or folds leave gaps that can cause false positive results.

  • 2

    Decontamination

    A validated H₂O₂ cycle creates aseptic conditions for the test. The primary packaging must be gas-tight – otherwise the agent can kill the very microorganisms the test is meant to detect.

  • 3

    Test execution

    During filtration and rinsing, antimicrobial product residues and H₂O₂ must be removed from the membrane. Any carry-over from packaging, media containers or gloves can contaminate the test.

  • 4

    Incubation and evaluation

    After 14 days of incubation, results are read visually. Slow-growing organisms such as Cutibacterium acnes may only become visible late in the incubation period – correct incubation temperatures, the full incubation time, dual control and traceability are essential for a reliable result.

Addressing the challenges

Securing the rest result

  • Preventing false positives: Barrier technology

    Isolators physically separate operator and sample and provide Grade A conditions. Decontaminable airlocks keep the main chamber aseptic during material transfer.

    → White paper: „The Testing of Pharmaceutical and Medical Devices for Sterility in an Aseptic Isolator“

  • Preventing false negatives: Validated processes

    Automated H₂O₂ cycles achieve a reproducible 4–6 log reduction. A product-specific method suitability test, gas-tight packaging and thorough rinsing ensure that real contamination is detected.

  • Reducing human error: Training

    Well-trained, motivated operators remain the most important prerequisite. Regular training, quality oversight and the dual-control principle at evaluation make manual steps more reliable.

Laboratory technician in protective clothing operating a SKAN spectra isolator through integrated white sleeves for aseptic pharmaceutical testing.
Addressing the challenges

Securing the test setup

  • Integrating the CCS: Risk-based control points

    An FMEA focused on the two worst cases translates the workflow into clear control points – from sample selection to quality oversight.

    → White paper: „Risk Assessment and CCS for Sterility Testing“

  • Handling product diversity: The right environment per sample

    Isolators are the safest choice whenever the sample allows. Large volumes or gas-permeable packaging need an adapted isolator or cleanroom concept.

  • Defining the background environment

    Authorities expect controlled access, temperature control, defined air exchange and room monitoring around the isolator.

Interior of a stainless steel sterility testing isolator from SKAN, hanging racks, and a small digital control display for regulatory-compliant pharmaceutical testing.

Expertise for reliable sterility testing

Reliable sterility testing requires more than equipment – it requires a deep understanding of microbiology, decontamination and regulatory expectations. Over the last two decades, isolators have become established state of the art for sterility testing, and SKAN has been developing them from the start.

We support QC laboratories in finding the right configuration for their needs – from chamber size and the number of daily tests to transfer systems, airlocks and integrated monitoring – and in integrating isolators into existing data historian, LIMS and MES environments.

Our support covers the full lifecycle: from configuration, FAT and qualification to cycle development, microbiological qualification, training and worldwide service.

Let’s talk about your sterility testing

Let’s discuss how to design a reliable, compliant and efficient sterility testing setup tailored to your samples and your CCS.

Our solutions for sterility testing

In dieser Kategorie sind derzeit keine Beiträge vorhanden.

Nehmen Sie Kontakt auf!

Ob Sie eine Frage zu unseren Produkten haben, technische Unterstützung benötigen oder mehr über unsere Lösungen erfahren möchten – wir sind für Sie da.

Zurück nach oben